Fluid Mechanics and Hydrology

Subject to approval of the Dean of Engineering and Forestry

ENCI241

Timetable Note

This is a lecture and tutorial-based course scheduled for the second semester. The course will be taught in two different formats. The first part of the course (weeks 1-9) will be taught using a flipped classroom format, where detailed recorded lectures of the material you are learning each week are provided on Learn and students are expected to review these in preparation for each week according to the schedule provided in Section 6 of this outline.

Each week will begin with a summary lecture and this lecture will run through the main concepts you have to learn for the week. Note that you are expected to have watched all the lectures for the week prior to this lecture so you are ready to ask questions during the lecture.

You are assigned a series of tutorials (with groups of 60 or so students) in lieu of traditional lectures for the remainder of the week. In these tutorials we will work through problems together to help you apply and learn the material you have watched in the lectures. You will need to submit your tutorial solutions for marking at the end of each session. You are assigned to particular tutorial sessions and submission of your tutorial in the wrong session will not be marked.

It is important to note that the tutorial sessions are designed to be introductions into the topics and your expertise in the material must be gained through further practice by working through the problem set questions and talking part in the online pipe design problems. Simply turning up to the tutorials each week will not provide you sufficient knowledge to pass this course.

The latter part of the course (weeks 10-12) will be presented in a traditional lecture/tutorial format with 4 hours of lectures per week supported by additional tutorial sessions.

Laboratory sessions will be run during the afternoons of the fourth term. These laboratories are designed to provide you with practical experience of fluid flows that will be discussed during the lectures.

The topics to be covered in lectures, together with the time and lecturer allocated to each, are listed in the following table.

Topic                    Time (hours)/stream                         Lecturer
Introduction                    1                                           McConnochie

Fluid Properties               7                                           McConnochie

Fluid Statics                   12                                          Lee

Kinematics &Conservation Laws  12                               Lee

Pipe Systems                    6                                          Lee

Hydrology                        10                                         de Vries

A detailed laboratory timetable will be provided. Attendance at laboratories is compulsory. If you cannot attend your timetabled laboratory class you must arrange to swap with somebody in another session of the same laboratory.

Course Coordinator / Lecturer

Craig McConnochie

Lecturers

Tonny de Vries and Pedro Lee

Assessment

Test and Exam: The test and exam are worth 80% of the final grade. The test will consist of a few problems and student solutions will be provided after the test session. These problems will be marked and returned to the students within approximately 3 weeks. The test will be conducted under conditions normal for an examination.

The solutions prepared by the students must be legible and well presented. Poorly presented material will be given 0 marks. If you suspect there is an error in the test or exam, you must make a reasonable assumption and proceed with the question. If there was indeed an error, you will not be penalised. Applications for aegrotats or special consideration based on errors in the test/exam questions will not be accepted.

Tutorials: Weekly tutorial submissions provide an opportunity for students to implement the ideas presented during lectures, with support from staff and tutors. They normally take the form of a problems class, where one or two questions are set and solutions are collected at the end of the tutorial session. Each tutorial is worth two marks. Students who are unable to complete the question, but are able to make a reasonable attempt at the question(s) will receive one mark for the tutorial session. The tutorials also provide an important opportunity for students to discuss difficulties associated with the material presented in the lectures directly with the lecturer.

As with the test, the solutions prepared by students must be legible and well presented; poorly presented material will be given 0 marks.

You cannot pass this course unless you achieve a mark of at least 40% in each of the mid-semester test and the final exam. Withdraws from the course will not be supported by the department subsequent to a test failure.

All  assignments  must  be  submitted  by  the  due  date.  Late  submissions  will  not  be accepted. If you are unable to complete and submit an assignment by the deadline due to personal circumstances beyond your control, you should discuss this with the lecturer involved as soon as possible.

The hydrology assignment can be done individually or in pairs. If done in pairs a single submission  for  marking  is  required  and  both  students  receive  the  same  mark.  It  is important that both members of the pair play an equal role in completing the assessment as the internal assessment is designed to prepare you for the formal assessments.

|"The laboratory report must be done individually.

Indicative Fees

* All fees are inclusive of NZ GST or any equivalent overseas tax, and do not include any programme level discount or additional course-related expenses.